Framewell Windows & DoorsGet a price →

FRAMEWELL MEASURING GUIDE

Measure once.
Order with confidence.

A good window project starts with good dimensions. This guide shows you where to measure, which number to use and how to deal with cills and rendered openings — clearly, step by step.

You can use photos or plans to start a Framewell quote. Before manufacture, final opening sizes should be checked carefully — and if you are unsure, ask your builder or installer to confirm them.
FramewellOPENING MEASURE
Width × 3Height × 3
01

Measure outsideBrickwork opening

02

Take 3 widthsTop, middle, bottom

03

Take 3 heightsLeft, centre, right

04

Use the smallestThen allow fitting tolerance

THE BASIC RULE

Three measurements.
One order size.

Openings are not always perfectly square. Measuring in three places helps you find the tightest point, which is the dimension that matters when the new frame has to fit.

1

Measure the opening

Work from the outside of the property and measure the structural brickwork opening, not just the visible frame you are replacing.

2

Record all six figures

Take the width at the top, middle and bottom. Then take the height at the left, centre and right. Record everything in millimetres.

3

Use the smallest

Choose the smallest width and smallest height. For a typical replacement opening, deduct approximately 10mm from each to create the order size and fitting allowance.

Measure the window opening in six places.

Three widths. Three heights. Always in millimetres.

TOP WIDTHMIDDLE WIDTHBOTTOM WIDTHLEFT HEIGHTCENTRE HEIGHTRIGHT HEIGHT
SMALLEST WIDTHyour smallest width
− 10mm
ORDER WIDTHuse for your project

For a window opening

  1. 1

    Start outsideMeasure from the outside face of the property, wall to wall across the brickwork opening.

  2. 2

    Measure width three timesRecord the top, middle and bottom widths. Do not assume the opening is square.

  3. 3

    Measure height three timesRecord the left, centre and right heights. Measure from underneath any removable existing cill where applicable.

  4. 4

    Use the smallest figuresSelect the smallest width and the smallest height. For a typical replacement opening, deduct approximately 10mm from each for the order size.

  5. 5

    Rendered opening?If render hides the brick edge, expose enough of it to measure to the actual structural opening.

Unsure? Do not guess.Ask your installer or builder to check the final manufacturing dimensions before you place the order.

THE DETAIL THAT OFTEN GETS MISSED

Measure from the
right cill point.

For replacement windows and doors with a removable existing cill, your height is normally measured from underneath that cill — not from the top lip you can see from outside.

  • Measure from under a removable cill unless you are deliberately keeping it.
  • Stone cills are different: measure the structural opening above the stone.
  • If the new product is being ordered without a cill, confirm the correct finished frame size with your installer.

Where the height measurement starts

CILL WITH A LIP
↑Measure from underneath the removable cill
CILL WITHOUT A LIP
↑Measure from underneath the removable cill

The key point: the order height needs to relate to the actual opening the replacement frame will occupy, not simply the visible top of an old cill.

FRAMEWELL GIVES YOU OPTIONS

Not ready with exact sizes?
You can still start.

One of the reasons Framewell is different is that an early project does not have to begin with a perfect handwritten schedule. Start from the information you already have and refine it before ordering.

START WITH PHOTOS OR PLANS

Let QuoteFrame find the openings.

Upload house photos or architectural plans and QuoteFrame can identify windows and doors and organise them into the project, giving you a faster way to get started.

Start a project →
HAVE YOUR TAPE MEASURE READY?

Enter your dimensions manually.

Use the guide above, record your opening dimensions in millimetres and enter them directly when you configure the windows and doors you want.

Get your price →

CHECK BEFORE MANUFACTURE

Good measurements make
for a better installation.

If anything about the opening is unusual — bay windows, non-square masonry, retained cills, extensions, cladding or render — share the project with your builder or installer and have the final sizes confirmed before manufacture.